Джон Бедини

The educational series covering clean energy technology towards building our children a future. Panacea-BOCAF is a registered non-profit organization, dedicated to educational study and research. All copyrights belong to their owners and are acknowledged. All material presented on this web site is either news reporting or information presented for non-profit study and research, or has previously been publicly disclosed or has implicitly or explicitly been put into the public domain.

Rick's site ­ For Bedini Fan kits and more

From Rick's web site

The Bedini process is very much underrated. Bedini's Free Energy book shows how the solar Bedini system can lead to much more useful energy being extracted from the PV panels. Note- Why does a solar panel drain a battery if there are no diodes? Very Simple: A Solar Cell has an Internal Resistance. Apply an External Voltage to it (From a Battery or Other source), and It Draws Current. Depending on the Applied Voltage and Current draw, This can also Destroy the Solar panel. The Diodes is required to prevent the Reverse Current flow. (Some Solar panels have a diode built into the panel.) When using the SG to charge batteries with solar panels, you must match the impedance of the panel to the SG. To do this you need capacitors at least 20.000 uf 75 volts we run the SG all the time this way. Set the SG to pull over 1 amp of current by setting the base resistor. The next question, is it a multi-coil machine, if so set it to pull over 5 amps min. The machinery to do this is anything but cheap, which in fairness John Bedini acknowledges. This is why John says there is no free energy. He has put LOTS of money and time into the R and D. The SSG and Fan device uses high voltage impulses to condition new and desulphate and recondition old batteries. This process can coax longer life cycles out of new batteries and recondition / bring back to life old batteries (batteries that can no longer be charged by conventional means). The SSG device can be constructed in many forms,, from very small to very large multi coil systems. A variation of the SSG device can be used to charge large banks of batteries. A variation of the SSG device can be used to help power itself while charging batteries. There still remains allot of research and development to improve the system. Battery swapping, the Bedini Watson flywheel, window motor and most impressive is the recent replication by Rick Friedrich which shows a "self runner". This is where Rick has recovered the mechanical power of the rotating bike wheel and directed it back to keep the battery charged. Many open sourced engineers have altruistically donated their time and effort into improving the system. This can be found by putting in "Bedini", "window motor", "self runner" or "SSG" in you tube and or Google video. This is an example of how open source engineers have worked with proprietary

inventors and improved their system. There exist political and economic conditions which john has been subjected to, (energy suppression) - not to mention scientific dogma which prevents the majority of the general public's access to the research and development into these types of systems. Not to mention media suppression as appears to be the case with myth busters. It is important that open source engineers continue working on improving this discovery and make use of what John has given to us all. What makes this technology an exception to every other aspect of current technology is that although it has been tested and made to work in some practical applications, it is yet to be accepted by the mainstream ethos and is not taught in any textbook that we have today. We have been told for around 100 years that there is only one way and not to question it, well it's time we do. John has chosen to learn a different science unknown to most people; this is like a painting that someone else may not understand, so they find no value in it. Mainstream science has given you everything at a high cost such as solar cells, wind generators, waterpower and so on, these are not free- energy systems, but people believe that they are, forgetting all the setup costs, they never pay back anything as they fail all the time, mostly the batteries. John's machine is a mass-less output system as he has said many times, John has said how the machine works. You must pay for the trigger or you can not have the energy, Tesla's system worked the same way, not free as someone had to pay for the trigger to the transmitter. The systems people seek require one trigger signal and then the machine can run itself after that. John states as a direct Quote ­ good luck, as you do not have the correct materials to make that happen. People make mysteries out of everything not the inventor, he just tries to explain it the way it works in his mind, and you are free to choose what you believe in. Most people do not even understand that magnets hold the answer as they are the real free energy machines; one charge and they run forever. If people could see where the energy is coming from they would be shocked as they would have nothing to measure it, it's only measurable after it's converted by the material in its makeup. ­End quote When discussing this technology on a public forum- it is important to moderate against disinformationist. The dis-informationists have been successful already in repelling john away from one of his own groups. Furthermore, it got so bad that Sterling Allan (group moderator) came in and shut the whole thing down. In the mean time, john still posts on Rick's private members groups. We continue to make great progress and are happily working together to further advance REAL scientific effort. Many experts posting to help one another, it's really great. The thing john said in the closed down SG groups was ­ "you can control the Bloch wall of the coil" this is hugely important and is the key to creating the asymmetrical systems. You need to take the dipole OUT of its perfect balance, at least momentarily. Note- Gel cells are not good batteries. While they can be used we do not recommend them. Rather flooded lead-acid true deep cycle types should be used.

Description

Panacea's replication of Rick's `Bedini's fan kit motor

John Bedini's Radiant energy technology is based on Concepts originally discovered by Nikola Tesla, John's process remains unknown by the mainstream. Applications include the most efficient Solar battery charging circuits in the world, curricular, house power and resurrection of dead batteries. The Bedini technology is a perfect tangible example of reproducible results which show Tesla's Radiant energy technology. Quote-The real question is does this machine charge your batteries, that's the real question. Does the energizer start every time you push it, or does it do nothing?' The purpose of this machine is just a teaching tool, there is no free energy to be found in the energizer, only in the charged battery if done right, but the mechanical is free that's the bonus with no more current input. If the trigger is done right the battery will charge with the lowest current input to the machine. The machine was designed to make it very simple instead of using timing sensors; you can do this if you want. The only adjustment you need is to adjust the base current resistor and that's it. The energizer then runs very fast. These pulses trigger the chemical in the battery to do a fine plating process window, this is how you get the extended time out of the secondary battery, that's where the energy is. It's funny no one has applied this to anything else. Done correctly you could apply this to an inverter and run the load while you charge another battery- John Bedini End quote. Back round informationPanacea's page on John Bedini Insights into the energy transformation process will be discussed in complete detail in the faculty information section of this course document. The Bedini process is typically used to charge lead acid (Gel cell) batteries. Other battery types can be used. There are many variants of the Bedini battery charging process. These can be run directly from a solar panel or a battery. Also an earth Rod can be used with a solar panel. The first configuration is the SSG (simplified school girl motor). SSG (simplified school girl motor)

lmichoux's SSG replication

The SSG is typically comprised of a bike wheel for a rotor and has simple circuitry. The Bedini SSG charging system does not operate the same as a conventional motor does, the Bedini process operates primarily as a mechanical oscillator. This oscillation involves interactivity of a coil and magnet which creates a high voltage spike. When the magnet passes the coil the circuitry triggers a signal in order for the right timing to capture the `pulse' so that a battery bank can become charged. A Video example of Ren's SSG -24 volt Bedini Cap Pulser Due to there being a mechanical oscillation, some consider this mechanical part of the SSG as free. Regardless, the SSG is low torque, but there is some mechanical that can be recovered without stalling the rotor. If this mechanical is not used, then it is a loss, but it is there and has already been "paid for".

Above is Lidmotor's practical example of using the SSG output ­ Solar Bedini SSG running a fan while charging batteries. Use it and your losses are reduced. If you just load your rotor with drag (be it via bad bearings, a piece of iron, aluminum or lead near the rotor) then you are just introducing a loss that can't be recovered. A generator coil, and or slave coil can provide some recovery, either passively or pulsed. An advanced variant is currently Rick's self runner circuit (described in the replication section). It is a common understanding that the rotor offers a `free' trigger. When the SG rotor is loaded for mechanical recovery, then the device has to be re tuned for its sweet spot (low current in- to high charging rate out). This is why sometimes, if an unloaded rotor isn't tuned right, adding a load can actually decrease the input current and the rotor speeds up, because the loading pulls the rotor into its sweet spot. Good bearings are essential if any mechanical is to be tapped. From this operation, one learns periodicity and how to use a compression point with an inductor to generate a higher voltage that can be deposited into a battery directly or into a cap to culminate into a higher charge potential before being released. One also learns how to tune the trigger method with resistance (along with other trigger methods should one go that route). This effect is happening in the chemistry of the lead acid batteries", the energizer is simply the trigger or waveform provider that shapes the impulse to cause the proper effect to be seen.

Wave form scope shot taken from a Solid state SSG

Quote ­That waveform can do wonders not fully explored yet. That is Tesla's time wave that he talked about. ­John Bedini From years of reading JBs work, one notices that he constantly mentions and stresses the correct waveform. It has also been discovered that the battery chemistry changes, with the correct waveform. The correct waveform causes the sulphation to be reduced and an oxide reaction to take place in addition to the normal sulphate-reduction reaction. One must remember not to confuse the normal sulphate-reduction reaction with the reduction of bad sulphate accumulations. It's great that everyone wants to experiment with variations of JB's design. However, they must keep in mind that the desired end-result is the production of the correct waveform. The waveform results in the production of an oxide-reduction reaction in the battery in addition to the normal sulphate-peroxide reduction. The waveform changes the battery chemistry. A correctly

constructed multi-coil energizer also has the added benefit that it allows an inrush of Aether energy to do all the "work" It is believed by some that the definition of "work" in this case is allowing the Aether to power the lead tetroxide-lead oxidation reaction. The energizer in the SG form will show the different chemistry and is a learning tool. It works well for conditioning batteries. The multi-coil machines will, when properly tuned, allow a big enough inrush of Aether energy that the batteries discharge more energy than was input to the drive battery.

John Proving his system is able to provide enough power to run a house!-Source

This is the essence of the "regauging" that Bearden talks about so much. It is believed that any experimenter trying to duplicate the work of JB needs to keep firmly in mind that the waveform is the final goal. The output from the SSG contains a HV component spike combined with a small current component. This current component is the "few electrons" that JB says we need and what is referred to by some as the threshold current. This threshold current puts the battery into a charge state, rather than its usual resting self discharge state. As the battery conditions (after many charge and discharge cycles), the internal resistance is lowered, (the plate surface area is increased as well) meaning that we need even less threshold current to place the battery into the charge mode. Over all this process is also a good basic experience with DC power sources in impulse current configuration. John has suggested testing the output of an SG machine using a 1ohm resistor. If you measure less than 1V on the output then clearly there is less than 1W actually charging the battery as far as conventional understanding is concerned. How is can 1W charge a battery at the measured charge rate? It cannot. Rick has proved this already, don't take our word for it, try the experiment for yourself.

Above is Rick demonstrating the one Ohm resistor test, you can purchase this video from Rick's web site

In this video Rick put a one Ohm resistor on the output of the SSG. He tested the temperature of the resistor before doing this, which was at 63/ 64F. Measurements done by a volt and analog amp meter showed the following results. Current showed 14 mili amps by an analog meter Voltage was 0.16 volts at peak Temperature stayed the same Do the math with the watts! Conventionally this is not enough electron flow or WATTS to charge a battery at the charge rate that is occurring in the battery. RADIANT ENERGY EXISTS! The final proof of this, can be seen by the temperature measurement of the one Ohm resistor when loaded, it did not fluctuate, or if current and or wattage was responsible for charging the battery, you would have heat as a result, even though a pulsating system, if you had a constant current situation, the heat would be PRESENT and be the tale teller so to speak.

Temperature test of the one Ohm resistor by Rick

This certainly suggests that something not adequately explained conventionally is going on. The voltage potential is charging the battery not current. John Bedini has also suggested using a neon lamp in line with the SG output to show the spikes going through as a further indication of what is going on. If you take the SG to be a learning tool, John Bedini tells us then by using pulsing technology with lead acid batteries there is something to gain. Rick's Fan kit

Panacea's replication of Rick's Fan kit

The Fan kit version of the Bedini technology is basically a cap pulsar with two power circuits; this is far advanced from a basic SSG configuration. The fan kit circuit makes use of the free mechanical oscillator part to perform real work with the fan (although you can attach on fan to the SSG circuit). If you calculate the input cost to the work being done by the fan and then add the battery charging energy (up to 4 batteries), you will then have a process like no other circuit in the world. TRY IT FOR YOURSELF.

Let's discuss this fan kit unit a little. We are able to run a fan which demands a certain amount of energy plus we are able to energize a second battery(s) to boot. If one is too use standard fan motor it will run down a small battery in no time at all - However the converted Bedini fan motor will be much more efficient and last much longer at good speeds plus- it sends a signal downstream to a lower battery(s) and recharges it all for the same cost. Rick has already put this concept to practical use; check out his ceiling Fan from Rick's web page. Multi Coil system So far the multi coil part of the technology has been developed into the most practical system for modern use (discounting R and D). This is not to taking any thing away from the potential of the other versions or systems; this is based on John Bedini himself showing a 10Kw house power circuit that needs not external power!.

John Pictured next to his 10KW house power system

Pictured above is John next to his multi coil system capable of powering your house and replenishing the batteries with no external input! IE- Solar or wind. This system does work THE MOST EFFCIENT with solar and wind. But can you buy it today? John stated publicly on the energy from the vacuum series, that he cannot sell this. Ask yourself why! John's hands are tied, we must help him. Further information on john's house power system can be found at: http://www.icehouse.net/john34/bedinibearden.html The Bedini pendulum or "Tesla gravity motor replication"

http://www.energyfromthevacuum.com/Disc2.htm

The following report was given to us by Peter Lindermann. Referring to Pendulum variation of Johns technology as seen in the energy from the vacuum DVD. This system it is designed to match the impedance on the batteries. All of the machines on the energy from the vacuum were test machines. Each one shown was designed to TEST something. Even the big 10 pole. Bedini said he wanted to see if it increased output with a much higher input via a big machine, it did not, there are hundreds of possible machines, some require some current. The machines in the video are now very old. The cole switch is from the 80s. If you study Bedini, he keeps moving so what we see are the left over (but purposeful) test machines he built to test a theory and move on. He has also said Solid state is the way to go, so everyone builds it and seems disappointed. Well, again, it is one way to do it, and TEST it, and figure out how it (the energy) works. John and I built all three pendulum machines together. I was there. The circuits were test circuits based on John's unique insights into this process. The circuits were John's, but I helped build the frames, pendulums, and coils. I also tested some of these units for weeks. John has not disclosed the circuits he used so I can't either. I will say that they were similar to SSG circuits, but not exactly the same. The system sent charge to both the run battery and the charge battery. I ran several tests where the run battery did not discharge AT ALL over a 4 day run. The charge batteries LOOKED LIKE they were charging very rapidly. The problem with the system was that the circuit returned ALL of the electron current to the run battery and sent pure Radiant Energy to the charge battery. After a while, the charge batteries all DIED!!!!! This helped prove Bearden's Theory that you need at least A FEW electrons in the system. Pure Radiant Energy does NOT charge batteries. All of Tesla's circuits show Radiant Energy lighting light bulbs and running motors, but NEVER charging batteries. Now we know why. The circuits are very counter-intuitive and you will never figure it out by guessing. The biggest energy effects came from the smallest unit. It was impossible to determine the energy gain in the system because it changed with the load impedance. In the end, the Pendulums proved Tesla's electricity fractionation process is real, since we were able to continually produce Radiant Energy impulses from a battery system that did not deplete. But nothing practical was ever demonstrated. As a battery charger, it was a failure. However, as a test apparatus, it taught us things about Radiant Energy that we had only been able to guess about before. The pendulum test set-up for the magnetic gate is not related to the later work on the electric pendulums.-End

A few replications have been done of this pendulum circuit and are included below. Bedini/Cole Window motor

Window Motor, Bedini/Cole ­this motor of John's has been on the same batteries for over 15 years!-Source

Another Variant of the technology done by john and Ron Cole, this is considered by some as the most advanced part of the process, as it has the potential to run for OVER extended periods of time (that's putting it mildly). Rick is also providing kits and parts for this on his web site. Solid state

Solid state built from the Free energy generation book

The improved and original solid state schematic can be found in the Free Energy Generation book by Tom and john. This eliminates the mechanical oscillation part of the circuit. Some consider it to condition batteries quicker than the SSG. This circuit is a perfect one to bring back dead lead acid batteries and charge them. Solar use is encouraged.

Jim Watson machine

Jim Watson's 12KV Bedni type converter (Bottom pic) presented at the Colorado Springs Tesla symposium.

This system was assimilated from John's ideas. The system had a pulse motor, flywheel and energizer. It was suppressed; more information can be found on John's Panacea page. Replication ideas are included in the replication section below. Imhotep radiant oscillator circuit

Lidmotor's -Bedini Fan fused with the Imhotep radiant oscillator

More background on this can be found on the panacea university site. Basically this circuit was originally intended to operate CFL lights. This has now been adapted to run with the Bedini fan and as a cap pulsar battery charging circuit. A brief description and full replication instructions are described below. Tesla Switch

This is a picture of the Tesla Switch built by Eike Mueller the load is 350 watt quartz light-Source

John also collaborated with Ron Brandt (a former college of Tesla) to build the "Tesla switch". This has SOME similarities to john's systems but it is not yet completely understood yet. A research paper on the Tesla switch will be included on the Panacea university site soon please check for updates.

Replication

Quote-I have harnessed the cosmic rays and caused them to operate a motive device. Cosmic ray investigation is a subject that is very close to me. I was the first to discover these rays and I naturally feel toward them as I would toward my own flesh and blood. I have advanced a theory of the cosmic rays and at every step of my investigations I have found it completely justified. The attractive features of the cosmic rays are their constancy. They shower down on us throughout the whole 24 hours, and if a plant is developed to use their power it will not require devices for storing energy as would be necessary with devices using wind, tide or sunlight. All of my investigations seem to point to the conclusion that they are small particles, each carrying so small a charge that we are justified in calling them neutrons. They move with great velocity, exceeding that of light. More than 25 years ago I began my efforts to harness the cosmic rays and I can now state that I have succeeded in operating a motive device by means of them. I will tell you in the most general way, the cosmic ray ionizes the air, setting free many charges ions and electrons. These charges are captured in a condenser which is made to discharge through the circuit of the motor. I have hopes of building my motor on a large scale, but circumstances have not been favorable to carrying out my plan. End Quote Nikola Tesla Brooklyn Eagle July 10, 1932 We suggest powering John's systems from PV solar panels, and then the input is free (ignoring the cost of buying and installing the PV panels of course). You can add other environmental inputs such as ground rods and aerials to boost this as well or even use electrets. Earth batteries will also be

discussed. Please read the PDF- Starters Guide BY RICK F, RICHARD L., AND RS in the replications links below to see specific differences between the cap pulsar's to the normal SG.

Simplified School girl ­SSG

John has stressed that the SG is a 1 to 1 charger, what you put in; you get out, no OU. But when you charge up to 4 batteries s from one battery that is a matched set, you get up to 4 charges for the price of 1, so long as you follow the battery rules. There are many different setups and they all vary in efficiency. By adding more batteries you get more total useful charge over time but not the equivalent of 100% per battery added in most cases. This all depends on the size of the batteries and their condition as well. Using two small batteries (one primary and one secondary) you usually do not get 1 to 1 charging, but more like 80 to 95% recovery. But when you place larger batteries, and several of them, on the secondary then you should get at least 1 to 1 charging in the sense of total work that can be done by them verses total work done by the primary. On advanced and well-built systems you may get 1 fully discharged primary battery for 4 fully charged secondary's. 1. Never discharge a battery or bank, faster than C20, anything less is ok up to a point, and on these small bats C24 rate is more like it. 2. Never go below 12.00V on the small bats, starter bats and marine deep cycles, and 10.5V on the true deep cycles golf cart, solar Bats, etc. 3. Because of the current less radiant spikes charging the bats, they will start to last longer at that C24 rate, and charge up faster every time, once they have been through a few cycles and conditioned. 4. Your coil or coils should match your matched set of batteries. If your C24 rate is .4 amp, than you can't pull a very big coil or only one coil, if the C24 is more like .8 amp than you can pull a larger wire coil at .8 amp, or 2 smaller wire .4 A coils that at their higher rpm might only pull .6 amp between them, if you have a big marine deep cycle batts it's C24 at something like 1.2 amp than you can pull a really big wire coil like Roamer talks about, or you can pull 2 .6 amp coils or 3 or 4 smaller amp coils sweet spot = highest rpm / lowest current draw point of a coil or coils, right before more resistance will make extra pulses. Bigger wire coil = higher rpm, more current,--- more smaller coils = higher rpm at less current draw for each coil because of the higher rpm, but more total current than just one coil and all this depends on your rotor number of magnets etc as far as what the sweet spot rpm and amperage is going be for a given coil size or number of coils running at that sweet spot rpm you want to charge as many bats as possible, from one rotor all the time, if you are not charging 4 bats from one bat even if you have to let the trickle charger make up the difference for a while, than you are not getting it. Pay for 1 charge, get your first charge back, and 3 charges for free, or pay for 2 and get 6 for free at a higher rpm. If you got it running so that you are getting the first one back and 3 for free, every time you discharge 1 of the 5, then as John says you should be jumping up and down. OK as John says, one more time, how much current coming from the drive Bat, vs how much current is going to the charging bat, is not what we are looking for here, when tuned to the sweet spot, the charging current will ALWAYS be FAR LESS THAN the Current Driving the Coil...!!!!!!! SO, what is charging the batteries? The CURRENT

LESS Radiant Voltage Spikes.. so forget about the in/out current ratio thing and LOOPING as that is not where the magic happens, it's really all about the batteries, and NOT about the motor.

Image is from Peswiki and Rick's site John Bedini said not to use neo magnets but 8grade fero magnets and than gradually add (go 2 or 3 per location) as needed .The magnets have to be identically spaced around the wheel. Unless this is the case, then monitoring with a scope while moving your coils around or will not accomplish much. The reason to have them all triggered together is so the voltage peaks will be additive. The whole phenomenon is about what happens in the vicinity of a very sharp "on". The sharper the better. Therefore, a tall peak is much better than lots of little peaks.

How does the neon work originally in John's circuit ? Is it always off, sometimes flash or just is always turned on? The neon lamp requires something around 85 to 95 volts across it before the gas ionizes and begins to conduct and give off light. If you have a healthy 12 or 24 volt battery connected downstream of the output diode, the voltage across the neon never gets that high, and it has almost no effect on the circuit. However, if the battery is badly sulfated and has a very high resistance, or the battery is disconnected, then the coil pops the voltage up very high as the transistor tries to turn off but has not finished that. When the voltage reaches the ignition voltage for the neon, it lights up, diverting some of the coil current through itself, and lowering the peak voltage that would otherwise be produced. Unfortunately, it is more of an indicator for this over voltage condition than protection during it, because it has a very limited ability to carry current. The NE-2, for instance is rated for less than a milliamp of continuous current, while the peak output current from the SSG can easily exceed a couple amps. Since the 2N3055 transistor is rated for 60 volts, collector to emitter, many will not last long with the 100 or more peak volts that happens while the neon is firing, valiantly trying to suck up that big current peak as its electrode atoms are sputtered all over the inside of the bulb by the intense bombardment of neon ions. If you see your neon blazing along, that means you need to shut down before you damage the transistor and neon bulb, and find out why the output current is not getting through your charging battery. The neon bulb is an "Oh shit!" indicator. Solar SG When using the SG to charge batteries with solar panels, you must match the impedance of the panel to the SG. To do this you need capacitors at least 20.000 uf 75 volts we run the SG all the time this way. Set the SG to pull over 1 amp of current by setting the base resistor. The next question, is it a multi-coil machine, if so set it to pull over 5 amps min. ­ John Bedini Roamers Schematic

Sourced from John's site 4 battery Rotator system This system is designed to run the fan or whatever tapped mechanical load continuously. As for a battery rotator, that is easy enough to do. Just get suitable relays that do not mess with the circuit and have them rotate over time or in relation to periodic voltage samplings. Ideally you would want three or four battery banks to give all batteries the needed rest periods for long life. We have to work with nature in its time as Bedini always says. We all need rest and so do batteries. After a battery is charged it should rest for while before being asked to discharge. 1)One battery being charged. 2)One battery power the front. 3)One battery powering a load. 4)One battery "resting" after being charged. The battery powering the front will charge more than one battery. For long life and maximum energy output batteries need a rest after they are removed from a charger. With a "conditioned" battery (explanation below), it will gain more energy for a period of time after it is disconnected from the charger. (Technically, the lead ions are still moving in the "charge" state and become a negative resister). They need time to come to a rest and ready for discharge. This is what John means by nature takes her own time. Note one CAN call conditioning it de sulfating the plates. SG circuit Slave

H-wave. Inductor in a Trigger Circuit Solid state Cap discharge with SCR and 555 Timer ­ An inverted version of the Cap pulsar by RS

This cap discharge circuit is solid state with the SCR and 555 Timer, and is a inverted version Cap Pulser. When referring to trigger switching, than this will be described as a rotor version vs Mechanical Switching. The BEST results reported were with the bicycle wheel one, 2000 turn trifilar, charging 198,000 uf to 2-4 volts above the dead battery, you of course have to adjust the pulley diameter in order to have it trigger at that based on how long it takes to charge the caps. Thread for technical discussion Aaron's Quantum key description of the cap pulsar Aaron's "the Quantum key" book is a GOOD summary of Tom Bearden's EFTV book. On page 107, last paragraph "I do not pulse the positive terminal of the capacitor to the dead battery's positive terminal. Instead, I leave the positive terminal connected and pulse the negative side of the capacitor to the negative terminal of the battery. It is not within the scope of this book to explain how this is different but it takes advantage of negative energy that is time reversed, and negentropic or self-ordering." There is in existence a john Bedini's inverted circuit with the 555 timer and the SCR on the negative terminal. But his description is perfect to connect the idea with the time reverse characteristic of negative terminal of the battery. SSG with lighting Variant by "the Dude" Quote-I've recently been directed to an excellent discussion on the Energetic Forum that was started by Imhotep. Here I've hooked up the coil from Imhotep's Radiant Oscillator to the power coil connection one of the Bedini circuits. I have to give the wheel a turn to get it oscillating and then stop it to get the transistor to self oscillates. I'm getting a decent illumination on 2 helicoil

16/20/24watt bulbs and a 15w fluorescent wired in series. When I disconnect a lead in the series of bulbs one or more bulbs continues to light! I'm not sure but is that a example of a radiant current flow? I just started with this arrangement and it seems to be giving my secondary battery a better charge than the wheel did on its own. Who knew? Maybe Tesla would have something to say. In case some of you want to try to get your Bedini circuit self oscillating and then hook it up to a ignition coil, this would be one way that works for me. I have to reiterate the fact that my oscillating setup seems to far surpass the radiant charging that the original design could produce. I hope John Bedini doesn't mind my borrowing his schematic. ­The dude End quote.

Tesla's High Voltage impulse lighting methods ­ Imhotep's radiant oscillator (PDF) The dude-My Bedini wheel with radiant oscillation ­ Project Website In conclusion We know the waveform we want from the rotor based energizer. We know the frequency we want, above 10k. can be tricked using a node in the wire we know the impedance matching we want from the charge battery (low) we understand at least partly what is happening in battery chemistry with the red lead. Overcharging will destroy it. We understand charging according to nature's time not ours. We trigger the battery into self charging with a time charge we want low electron flow to the charge battery this is just a few of the clues that can be compiled. SSG links How to videos by introvertebrate

Earth Battery and Earth Rod SG By Aaron

From the beginning, John has shown that you can ground the sg to the earth. Look carefully at the following:

The following picture is what Below pic is what I'm pointing out:

Unfortunately, most people haven't paid much attention to these details. In Aarons diagram:

I show something else. The zinc rod from the SG's ground is going to earth. That is a real GROUND. The Earth may or may not be used as an electron source. You can get a POSITIVE radiant potential

(voltage potential) from the Earth and this has nothing to do with electrons. My diagram shows Bedini's ground as she has shown in front of everyone for years but hardly anyone noticed but a few. The other copper rod is what Kevin had on his setup in addition to the goofy magnet setup when getting way over 1.0 COP. Thing is, Kevin didn't even have the regular ground rod from the neg on the system...just the rod with diode to the + on the charge battery to absorb radiant potential from the earth. This diagram is putting BOTH of them together. It will be obvious to anyone that has experimented with Earth Battery setups that looking at my diagram, both rods together obviously form a basic earth battery or a real potential difference at both rods...about 2-4 volts can be easily expected almost anywhere at minimum. You have to poke around a bit to get above 2 volts but you can find it. The battery, better if large plates or of other construction like Bedini shows on his site, intercepts and soaks up earth currents and entrains the earth currents there. What can be expected out of doing this? Everyone has to do their own experiments but what Kevin and I have found is that the charging effect in the output battery increases. You can see where the diode leaves the copper rod and goes to the + on the charging batt...there are other places you can put it but you have to explore that on your own. Just see the SG for what it is...it is a gas valve and all concepts of gas pressures apply. What do coils do and how are they pumping this gas and how do you get low and high pressures and putting that together with what is sitting on that diode on the copper rod, well some things should reveal themselves. In Aaron's replications the Cap is charging by pulling the negative and not pushing into the positive.Works better the deeper you go with the metals. Works better with more mass. It is easy to get about 2v if you look around. I've gotten up to 4v with 2 rods but seem hard to find that. The main purpose of Aarons replication is just to show that there can be real practical effects to be had from an Earth rod. He just hope others use their own creativity and innovation to see what they come up with. There are different ways to utilize the pos potential rod and neg potential rod. If a neg rod is connected to a capacitor's negative for example..Even with one wire...if the "Earth battery" has a potential difference at its terminals great than the capacitor's terminals, the negative line will form a suction on the negative terminal on the cap and will create a bigger net positive pressure in the cap. You are forcing the negative on the cap to become a lower negative (by suction of the lower negative potential) than it was before and that creates a larger potential difference between the negative and positive terminals. You did that not by even doing anything with the positive but only by manipulating the negative or lower potential side of the system. If the earth neg is a lower potential than the neg it is connected to on the circuit, it will then act as a sink to give a more "conductive" path for gravity to channel more potential through the system. The Earth Battery will actually grow stronger and stronger over time. The rods I show is not really an Earth Battery but does demo the potentials are there. One of the tricks on an Earth Battery is to keep all the terminals from shorting each other out. Earth Rods by Aaron

One thing to realize about Earth Rod applications from my experience is that the results are NOT consistent. This doesn't mean that you can't always have positive benefit; it just means the results change over time. ALSO, depending on other variables, the results can GROW over time. I have shared this concept with a few Bedini experimenters and have received such a wide range of reports. I'm sure the geography has a lot to do with it...where are the Earth's acupuncture meridians in relation to the rods, etc.I used to have Earth Rod systems going to grids laying under a bed mattress for healing purposes at a house about 7-8 years ago. John Bedini turned me onto the Earth Rod concepts back then. A good way to find a good spot to put a rod is to get a multimeter and put it on DC volts. I had some long wires and alligator clips attached to the ends of the probes and the other end I had 3 foot rods...one steel and one copper. I would put one rod in the ground...doesnt' matter what rod you use for what charge because you're just looking for the largest potential difference you can get. One rod in ground...deep, then take the other rod and walk around with it sticking it in different spots. Wherever you get the highest reading, leave the second rod there. Then mark where the first rod is, take it out and see if you can find a higher reading with it somewhere else, if not, put it back. If you get a higher reading, you can take the other rod and move it around and go back and forth. You're lucky if you can get 2 volts. I found 4 one time in my Qigong Master friend Rodger's backyard. Anyway, this will show you some good spots either plus or negative. For the TRV discovered rod method, it takes one rod...not for grounding purposes but to draw the Aether from the ground. EARTH --- ROD --- DIODE --- POSITIVE ON CHARGING BATTERY

That's it! The TRV session was for logical next step enhancements to the overall SG circuits and with research combined with the data, the above is what it revealed. The line on the diode should be on the side of the battery so the positive voltage potential moves from Earth TOWARDS the charging battery positive terminal. This is so easy for ANYONE to do that I would recommend that everyone at least play with it and try other variations if you want but the above is the exact method that was used on Kevin's SSG with the alternative superpole magnet configuration. Also, try potash around your earth rod ground, like Kevin does, with the ground rod going through a diode to the positive terminal.

Earth battery and Earth Rod SSG links Technical discussion ­Energetic Forum Experiment: Ground Antennas By Gerry Vassilatos & Michael Theroux John's coverage on Earth Batteries PowerPedia:Earth battery Directory:Earth Batteries Earth-battery-sg-2- energetic forum thread

SSG Links Starters SG guide BY RICK F, RICHARD L., and RS John Bedini Monopole Mechanical Oscillator Simplified School Girl (SSG) Presentation- By Rick PesWiki coverage

Rick's Self Runner

Source Complete reports and background can be found on the PesWiki page listed below Koneheadx Self runner recovery Try a FWBR AC legs across your motor switching, and just one AC leg of FWBR gets switched ON-OFF in echo-pulse to initial motor pulse (DC side of FWBR into load)Try it ­ it has nothing to do with any stupid laws (scientific slogans really) just makes your motor run faster, more powerful, with less draw.Forget about batteries if you are sick of them ­ re route backemf/recoil into 2nd set of coils like Ian Coke-Richards "butterfly" circuit see on his site: http://www.mintakafulcrum.net/ "Condition" the backemf/recoil that makes the "volts climb" in batteries...do this by putting it into DC CAPACITOR FIRST...then pulse-out cap into battery at near-twice the voltage of battery being charged (23V in cap if 12V battery) Batteries don't really like or accept the quick pulsing rate that runs motor coils ­ they like to "slosh" so go much slower rate with battery-charge pulses. Self Runner links http://peswiki.com/index.php/Directory:Bedini_SG:Self-Runner Energetic forum discussion and ideas Translated site with a tutorial of the self runner

Multi Coil system

Introduction by John Bedini-Rather then get into a big discussion over what material is better for the rotor at this point, I want to point out a few things. As I said in the beginning this is a simple machine to just prove that you can have a machine that supplies mechanical energy to do something with no matter how small that is. It's the first machine that runs does the work and charges a battery, it recovers all the waste energy in the circuit and supplies it to a secondary battery, don't you wish you had a toy like that, because it is toy sized, but toys make "big machines". You can alter it to charge capacitors if you wish. You can screw it all up with any circuits you try and improve it with, hopefully it will work the way you want it too, just like a textbook motor, no recovery. If your circuit is working correctly no transistors get hot and coils do not melt. A multi coil machine must be balanced, that means all the currents in every device. Base resistors, transistor bata, coils, why the twisted coils, to keep the capacitance and inductance the same. If the transistors are not the same heat on all, something is very wrong in the way the base circuit is working, also this could mean a bad transistor in the bunch. Fet's, do not work well here, wrong capacitance to hard to drive without a driver circuit. Opto circuits work fine, hall works fine but it is a waste of current when trying to get COP>1. Why such low current on the input, so you get more radiant voltage potential. Voltage first, current last = time in switching, long switch time more current no COP>1. Current builds up no radiant voltage. I also said the high voltage is part of the surrounding 3D 31eservo field, you do not half to agree with me on this as you must see it the way the text states it di/dt, rate of change in the coil. What you forget is Q1+Q2+Q3+Q4+Q5+Q6> is additive and subtractive with the magnetic fields during the rate of change while the rotor is rotating in the 31eservo field. Instead what I get is complaints for trying and suitable insults with those that just do not understand what this means as an application. I made the machine so anybody could build it with junk, very little cost to prove a point. Yes it is possible to get COP>1 with it. I found the welding rod to work the best overall which you could get very easy anywhere, point 1. I used ferrite # 8 magnets you could get anywhere. Point 2.I used a normal solder roll for the core. Point 3.I just took normal wire to make the windings nothing special. Point 4. I used anything to make the Rotor as it did not make any difference as I was just looking for a "trigger signal", point 5 you could figure an exact coil and it would not be any better. It's the trigger that is important. It's not a "Riddle" when you understand the machine. All the other coils are slaves. You may add as many windings as you need on each coil, the main coil has one extra winding, the trigger winding. All the transistor bases are summed together to a common buss with their base resistor's, all the output diodes are summed together on a common buss connected together also. All the rotor magnets must be in perfect alignment to the pole piece's all magnets must be measured for gauss to be equal within 5% min. I would also measure transistors for Bata as this will effect the machine. All the gaps must be the same. I do mine with a gap gauge from pole to pole 5 to 10 thousands will work fine, it's the only way you get a good wave shape. Remember what the H wave shape looks like, the same as the solid state nothing can be different.

A six coil machine should be around 5 amps input current @ 12v. alltransistors are mounted on a small flat heat sink. The base trigger coil circuit must then have a series resistor in series with all the summed transistor base circuits. It is much easier to build a 11 strand coil on the simple SG machine with 23 wire all twisted together at 100 feet on a 5 inch bobbin ѕ inch hole. This is not a easy machine to build and not shown on the diagram-JB A youtube video of a 9 wire just as John describes scalar north rotor, with waveforms. There are lots of tricks for setting up and tuning a multicoil. You only need one trigger winding and one globe etc if all coils are to fire at once. You need to get it firing on one coil, one winding first. Once you know you have that coil and power winding firing you can move onto multiple transistors. All bases must have the same resistance but that resistance can't be too high otherwise it just won't fire. Get one running and tune it and you will have a fair idea of what base resistance to use. Reversing the trigger coil could fix your problem, if its polarity is around the wrong way it won't work. Now, one thing that John has mentioned is to try wrapping all 25 strands of a 6-coiler onto one single larger coil form instead of using 6 separate coils. Lee's diagrams

Slave Coils Jpeg John's Multi coils walk through Dan Breeden's Handy SG/Multi coil Builder's Guide

Dan's version of SG under construction

INTRODUCTION: This build instructional guide is an attempt to encourage more people to

replicate the 6 magnet energizer as built by John Bedini. Some people are good at electronics and poor at mechanical stuff. Others have no idea where to get weird parts where they live. I've tried to design this version with readily available parts. The main thing is that nobody wastes a penny on components that are unsuitable.

This idea started in mid 2006 when I suggested to the SG list that we change to a second version and try to standardize as many components as possible. I proposed that this V2 be based on John's 6 coil machine. I machined rotors and sold them at cost. I could see from correspondence that some people were building constructs that weren't a good design. This "book" is a collaborative effort to show one way to build a Bedini energizer. There are many ways to build.

Use of non-ferrous construction materials

RULE 1: "Everything interferes with the radiant energy so I built with Plexiglass" ­ John Bedini. If that's John's rule, then it's the rule here too.The materials are Wood, Plexiglass, Fiberglass, Plastic, Phenolic and other non-conductive materials. Search on "eddy brake" to see why the frame isn't made with copper or aluminum. The bearings are the only stationary parts that are conductive. The coil, core, conductors and semiconductors are necessary exceptions. The coil is where the radiant energy is "transduced/attracted". When the energizer is humming along nicely, it will affect iron or a gauss meter up to 5 feet away. Small fasteners may seem innocuous, but they have a negative effect. Anything that is conductive will distort the field of the coil. JB glues his components together. This design isn't as elegant as John's but it's meant to be a workhorse rather than a showpiece. You're free to change anything that you want, but remember rule #1.In general, all machinery is jigbored for alignment of the bearings. This design uses self-aligning bearings to avoid that necessity. JB uses a stainless steel axle. I use aluminum because stainless steel averages 26% iron. You can test it for yourself but, different axle materials cause different results.

GETTING STARTED: he main platform starts with 2 pieces of material 24 X 24 X 1 inch. For a 2

T

rotor machine, 28 X 28 X 1 inch is necessary.

Center finder is a great help

This little gem will find the centers of both circles and squares. It's a center finder. It's especially useful when the corners are beat up. Use it to draw your diagonals. The center hole is your first reference, the diagonals are your second."A center-finder is a great help. I laid my new center-finder on a corner. I drew a line and flipped it over to draw another line ­ same corner. There was an 1/8 inch difference. Check it before you believe it?" ­ Dan Breeden

Ice pick as center punch

Use an ice pick to punch a small indentation at the center point which will act as an anchorfor the compass.

You can do almost the entire layout with a compass. An extra lead for the pencil part is handy.

This handy device is for drawing circles. It's available from drafting/art supply stores. They're called compass points and they slip onto a yardstick. Some newer yardsticks are too narrow so beware and check the fit before you make your purchase.

To begin, put the point of the compass in the center hole and the pencil point out near the edge. Leave enough room so that the spacers aren't right at the edge. Scribe a nice clean circle.

Preparing to layout 60 degree marks

Lay a scale [ruler] on the diagonal. It's easier if you clamp it. Take a 30-60-90 draftsman's triangle and lay it on the diagonal with the corner at the center hole. The side of the triangle will be at 60 degrees to the diagonal.

Use of compass to mark 60 degree points around rotor position

You can use a second scale as an extension to reach out to the circle. If the point of the triangle is at the center hole, the 2 scales touch the circle at exactly 60 deg. Put a small mark with an ice-pick. Put 1 side of the compass at the point where the first line touches the circle. Put the pencil point of the compass at the second line where the circle touches the straight line. Tighten the adjustments and then go around the circle marking this length section by section. You should end up back at the start with 6 evenly divided sections. If you mark off 3 sections to the left and then 3 to the right, You'll have half the error. When you're happy that the 6 sections are even, scribe 6 lines out from the center point. These are your third reference points. At these 6 points, drill a 1/8 diameter hole, ј inch deep.

Eye ball center location for rotor position. There is adjustment room built in.

Lay out the rotor and coil mount. JB has the coil mounts under the coil for

compactness. I put the coil mounts outward to make them more accessible. Put the spool right against the rotor. Mark the 2 slots in the coil mount onto the wood.. You can build with the coils in line with the spacers or between them. You will have 2 elongated circles. Put a mark 3/16 inside from both the inboard and outboard edge of the elongated circle on center.

Hopefully, you started out with 2 perfectly matched pieces of material. Phenolic is the

best followed by Plexiglass [42eservo], next is hardwood; Maple or oak. Last is plywood.Clamp them together perfectly even. At the very minimum, 1 edge has to be perfectly matched. Drill the 6 pairs of holes using a spade bit. Drill to finish size. Drill to Ѕ" for fiberglass rod or 7/8" for plastic pipe. Next is the center hole. Use a hardwood or plexi block as a guide. Use a drill press to drill a 1/16 hole in a block. Then use a pistol drill to put the bit through the block. Align the exposed tip of the drill bit in your center mark. Push down on the block and then drill the hole through both pieces of material. You only want a hole big enough for the point of the compass.

Completed hole layout

Use the compass to make equal marks in each of the 6 sections.

You need to drill